Your furnace is an integral part of your home. Without one, you wouldn’t be able to stay warm during the winter. Yet furnaces can have some issues that are more common than others.

Let’s go over these issues and discuss what they might cost to fix so you know before you contact an HVAC technician. Some of the most common furnace repair problems include:

  • Furnace won’t turn on
  • Furnace doesn’t stay lit
  • Furnace won’t blow hot air
  • Furnace won’t turn off

1. The Furnace Can’t Start

There are a couple of reasons why your furnace won’t turn on, so make sure to check all of them.

  • Is your thermostat set correctly? Make sure it’s set to “heat,” “auto” and that your desired temperature is greater than the room’s current temperature. If you use a programmable thermostat, make sure it has fresh batteries.
  • Is the circuit breaker tripped? Your furnace can’t operate if it doesn’t have electricity. Reset the switch if it’s facing the outside of the electrical panel.
  • Is the furnace switch off? Your furnace has a power switch found on or close to it. Because this switch looks like a light switch, it’s easy to accidentally turn it off. If it was off, it might take your furnace a few minutes to start.
  • Is the air filter clean? A dusty air filter can create a lot of issues for your furnace. Replace yours if you can’t see light through it.

Estimated Repair Cost

This problem can be complicated, so the estimated cost to repair it depends on what’s wrong.

2. The Furnace Won’t Stay Lit

Your furnace uses a specific sequence when it starts heating your home.

  1. Your thermostat notices the temperature has fallen and tells your furnace to turn on.
  2. The draft inducer fan activates to pull in fresh air for combustion.
  3. The gas valve unlocks for the burners, which are ignited electronically.
  4. The flame sensor tells your furnace the burners have been lit.

If something is off during the sequence, your furnace will shut off as a safety precaution.

A couple of potential causes for this issue include:

  • Dirty or malfunctioning flame sensor. If the sensor doesn’t detect a flame, it will shut off your furnace to keep natural gas from spilling into your home. The ignition process corrodes flame sensors over time. While cleaning during annual furnace maintenance can help, yours may eventually need to be replaced.
  • Bad limit switch. This safety feature will shut off your furnace if it senses backdrafting. Backdrafting is dangerous, because carbon monoxide and natural gas can seep into your home. These switches can fail due to age, damage or dust accumulation.
  • Old thermostat. If your thermostat isn’t working properly, your furnace won’t be able to operate.
  • Dirty air filter. A dirty air filter can limit airflow and force your furnace to shut down to prevent overheating. Make sure to change yours every 30 to 90 days, or anytime you can’t see light through it.

Estimated Repair Cost

These costs are estimates, so it’s necessary to note yours may fluctuate based on your furnace’s brand and model.

  • Flame sensor: $350–$500
  • Limit switch: $150–$300
  • Thermostat: $150–$350
  • Furnace filter: $10-$30

3. My Furnace Is Blowing Cold Air

In many instances, this problem is tied to a wrong thermostat setting or a dusty air filter that’s restricting airflow. Use the steps above to resolve the problem.

4. The Furnace Can’t Stop Running

If it’s extremely chilly outside or you like your home to be toasty, your furnace may be working for a long time.

If this isn’t the case, make sure your thermostat is set correctly and running properly. If your fan setting is at “on,” the blower motor will be running even when the furnace isn’t, so it’ll sound like your furnace is running all the time.

Otherwise, there might be a problem with the blower motor or your ductwork may be losing air, forcing your furnace to run continuously to make up for the air loss.

Estimated Repair Cost

These costs are estimates, so it’s necessary to note yours may vary based on your furnace’s brand and model.

  • New blower motor: $250–$800
  • Seal ductwork: varies based on square footage

Alpine Summit Heating & Cooling Can Resolve Your Furnace Issues Quickly and Affordably

Furnace problems can be an expensive headache, but not when you call Alpine Summit Heating & Cooling. We’ve been delivering the quality, affordable furnace repair Athol homeowners have relied on since year. Contact us at 208-561-1226 to receive your free estimate today.